NET-DEV module with 4 changeover relay outputs (12A)

Name: NET-DEV module with 4 changeover relay outputs (12A)
SKU: NET-DEV-REL4_UM_12A
Price: 243.50 EUR
Availability: InStock

Rated 0 out of 5

0 customer reviews

€ 289,77

incl. 19% VAT plus Shipping Costs

Desined-in-Germany

OUR PROMISE TO YOU:

Our advantages

New feature!

Extended input filter for Digital-IN / Timeout protection function for Digital-Out.
For more information, see the Description and Technical Data tabs!

Availability: In Stock SKU: NET-DEV-REL4_UM_12A Category: NET-Series

The NET-DEV-REL4_UM_12A module has 4 changeover relay outputs with 12A switching capacity each. It serves as an extension possibility for the NET-CPU basic modules and is integrated into an existing NET system by means of Plug’n Play plug connection (DIN Rail-Bus).

4 relay outputs changer (CO)
Max. switching voltage: 48V AC / DC
Max. current carrying capacity: 12A
Timer Function
Timeout output protection
LED status display per output channel

Digital outputs

Relay 12A

This module uses 4 changeover relays (CO). They are suitable for medium switching capacities up to 12A and have a mechanical life of up to 10 million switching cycles. The galvanic isolation between input and output circuit is up to 1.0 kV.

Fail-safe mode

The fail-safe mode is a safety function in which the DEDITEC module switches to a previously configured, safe switching state in the event of a connection failure.
This is intended to prevent connected installations or systems from continuing to run in an uncontrolled manner.

Three switching states can be defined for each digital output: a) Switched off, b) Switched on or c) Unchanged.

The fail-safe circuit is triggered by a timeout protection function. If the control unit no longer receives any commands from the control PC within a previously defined period of time, the timeout function comes into effect. The cause of a timeout can be a loss of connection between the control PC and the DEDITEC control system or failure of the control PC.

Timeout modes

Three timeout modes are available:

A) “Normal mode” is valid once and must be reactivated manually by software command after each timeout event. The customer application still has access to all controller outputs.

B) In “Auto reactivate mode”, the timeout function is automatically reactivated after communication with the control PC has been re-established. The customer application still has access to all outputs of the control unit.

C) The “Secure outputs mode” blocks access to the outputs after the timeout event. Unlocking can only be carried out by software command. This is an important safety aspect

Timer Function

All digital outputs of the NET series have a timer function. This allows the outputs to be switched on and off automatically for a freely definable period of time. Even if the connection to the control PC is interrupted.

Easy installation thanks to DIN rail bus

Thanks to the practical NET-Bus connector, which is clipped into the top-hat rail, individual modules of a system can be added or exchanged very easily. This Plug’n Play principle makes commissioning easier and eliminates the need for tiresome wiring.

LEDs

On the front side of our NET modules there are a number of status LEDs. These give you a quick overview of the most important functions of the modules, such as the switching states of the individual I/Os, module status or whether clean communication via the DIN rail bus is possible. This can be very helpful for fast error analysis, especially for field applications.

General
Power supply	Internal, via the DIN-Rail Bus
Power consumption	Max. 130mA/24V
LEDs	• Internal bus communication • Module Status • Two LEDs per relay output
Timer Function	Automatic switching on and off of the outputs within a freely definable time period
Connectors	• Typ: Phoenix Contact 1975118 • Push-in spring connection • Without switching capacity! • Connection for all conductor types from 0.2mm² to 2.5mm² • Pluggable
DIN Rail-Bus	NET bus connector for connection to further NET modules
DIN rail mounting	TS 35
Operating temperature	+10°C to +50°C
Dimensions	135 mm x 22.5 mm x 111 mm (H x W x D)

Digital outputs
Timeout-Protection-Function	• Simple and uncomplicated setting of the timeout protection function possible via software • Time-definable automatic activation of the timeout protection function in the Timeout case (between 0.1 seconds and 6553 seconds) • In the timeout case, digital outputs can be activated, deactivated or left unchanged
	• 3 different timeout modes: “normal”, “auto reactive” and “secure outputs” for different procedures in case of a timeout event. In “secure outputs” timeout mode, access to the outputs is blocked after a timeout event, thus preventing further access to the outputs. Unlocking must be done by an additional software command.

Relay outputs
Relay up to 12A	• Type: Finder 41.61.9.005.0010 • Property: Changeover contact (CO) • quantity: 4 • Max. Switching voltage: 48V AC / DC • Max. switching current: 12A AC / DC • Max. switching capacity: 576 VA • Galvanic isolation between contact and coil: 1kV RMS /1 Min • Mechanical life: up to 10 million switching cycles

[vrm360 canvas_name=s1 model_url=/wp-content/uploads/2021/01/NET-DEV_REL4-1.obj aspect_ratio=2 initial_offset=1.5 autostart=true lightintensity=0.05 amb_lightintensity=1 button_color=#cc0000 border_width=1 border_color=#acacac backgcolor=#f8f8f8]

Additional information

Weight	0,169 kg

General information on the ICT tool

We have developed the new ICT tool to make commissioning our products as easy and straightforward as possible.
This tool combines all the important functions of our old programs, such as the Configuration Utility, Module Demo and DT-Flasher, in one.
With the ICT tool, you can now easily configure, test, diagnose, flash and debug our products.
In the following chapters, we would like to introduce you to our new all-in-one software in more detail.

Module selection

Here you can integrate your modules into the ICT tool by clicking on the “+” symbol, so that you can then configure or test them.

Start screen

Here you can find some important information about your selected module.
In addition, you can display the manual of the module as PDF or HTML version here.
Under “Show module IDs” you can call up all available module IDs. This ID is needed to integrate our products into your software projects.

ICT Treeview

In the treeview on the left side of the program window, you can see the respective forms that are supported by your module.
With a click you can then display this form in the right part of the program and perform possible configurations or tests.

Information on the configuration area in the ICT tool

Info

Here you can view all important module information at just one glance.

Modul-Name
Modul-ID
Firmware-Revision
Interface-Type
Current DIP switch setting (Ethernet modules only)

Identification

Identify your Ethernet module currently addressed by means of LEDs located on the board.
This is especially helpful if several modules are in operation at the same time.

USB-Configuration

Here you can change the module no. of your USB modules. This is necessary if you use several USB modules of the same series.
The module no. can be used to identify exactly which module is to be addressed.

LAN-Info

All important LAN network information at a glance. On this information page, you will find the current LAN settings of your module.

LAN-Configuration

Integrate your module into the home or company network with just a few clicks or control it directly via a 1-to-1 connection.
The following network settings can be changed with the ICT tool.

Boardname
DHCP on/off
IP address
Subnet mask
Standard gateway
TCP Port

WiFi-Info

This page shows you all the important WiFi settings.

WiFi-Configuration

Here you can change the network settings of the selected WiFi product.
The following settings can be made:

Boardname
WLAN on/off
Routername
Routerpassword

WPS

With the WPS function, your module can be quickly and easily, automatically connected to the router (WPS on the router is required)

CAN configuration

With our CAN products in the BS, NET and UC series, settings for the interface and the TX/RX packets can be made using the
ICT tool.
More information can be found here: CAN configuration

Serial configuration

With our serial products in the BS, NET, UC and RO series, changes can be made to the interface using the
ICT-Tool.
More information can be found here: SER-Configuration

TCP encryption

Here you can make settings for the encryption of your module.
The following configurations can be made.

Allow unencrypted protokol on/off
Allow user-encrypted protocol on/off
User-encryption password
Allow admin-encrypted protocol on/off
Admin-encryption password</li
Allow I/O access via webinerface on/off</li

NTP-Configuration

Here you can make changes to the NTP service.
The following configurations can be made.

NTP service on/off
Server
Port
Timezone

WEB-Login

Here you can change the login settings of the web interface.
The following configurations can be made.

Session Time
Account name
Account password
Confirm password

D/A Default Values

Here you can set the D/A values and modes with which the module is to be started.
Value and mode can be set individually for each channel..

Watchdog Configuration

Here you can make and save settings on your watchdog stick.

Save or Load config

Using the “Save or Load config” function, you can save your entire module configuration in an external XML file.
This way you can always load your module in the original state you want. The following configurations can be saved depending on the module type.

USB configuation
LAN configuation
WiFi configuration
TCP encryption
NTP-Configuration
Serial configuration
CAN configuration

Information on the I/O test area in the ICT tool

Digital Out

Here you can switch the digital outputs of your module on and off.
The following functions can be tested in this form.

Switching the digital outputs on and off channel by channel
Readback of the channels
Setting a digital output for a certain time (module-dependent)
Specifies which status the channels are to assume after the time has elapsed (module-dependent).
Testing the outputs

Digital In

Here you can read out the status of your digital inputs.
You can take the following information from this form.

Channels status
Number digital in counter (module dependent)
Flip Flop status (module dependent)

TTL I/O

Here you can switch the digital outputs of the module on or off.
In addition, you can set the TTL direction for up to 8 channels block by block. This setting remains until the module is restarted.
The following functions can be tested in this form.

Switching the TTL outputs on and off channel by channel (TTL output)
Output Readback
Testing the outputs (TTL output)
Input Readback
Set TTL direction

Analog Out

Here you can set the analog outputs of the module.
You can set the D/A value and mode for each channel individually or all together..

Analog In

Here you can read the A/D – value of the channels.

In addition, A/D mode and filters for all channels can be set here.

CAN Runtime Parameter

Here you can change CAN settings of the interface, RX and TX packets in runtime

Baudrate
Extended ID
Active on/off
CAN-ID
Mode

CNT48

Here you can read out the count status of your counter module.

Puls Generator

Here you can test the channels of our pulse generator modules.

PWM Out

Here you can make settings to the frequency of the PWM channels.

Temp

Here you can read out the created temperatures channel by channel.

Graphical representation

Here you can display the measured values of Analog In, Temperature or Fifo-IN graphically.

IO – Timeout

With the help of the timeout function in the IO area you may simulate a timeout event of your module.

Indicates by flashing, the connection to the module
Removing the checkmark triggers a timeout event
The user interface can be updated here after a timeout case Manuel
Shows the current timeout status
Here you can set the timeout mode
Here you can set the time in which the timeout should be triggered
Enables / disables the timeout

M2M-CAN

Machine-to-machine, or M2M for short, involves direct communication between two or more modules. Analog or digital data can be sent channel by channel from a source module via the CAN bus to channels of one or more target modules. All products that have a CAN interface are supported. For communication via CAN, the controlled modules only need to be connected to the CAN bus.

M2M-CAN Configuration

In this example, CAN packets are sent every 500ms via the CAN bus to CAN ID 700
These settings can be made in the ICT tool in the CAN-Config area.

For precise and constant reading and writing of measured values at very short intervals, we have developed the software FIFO (“First in-First out”) for our NET series products. With the help of this software, the measured values that are sent from the PC to the NET module, for example, are temporarily stored in a FIFO buffer. These are then processed independently by the module at a defined time interval.

To put it simply: measured values are collected and stored in the buffer for both “FIFO In” and “FIFO Out” and then passed on in packets. This eliminates delays caused by traffic, spatial distances or other disruptive factors and significantly improves measurement processes.

All the advantages at a glance:

Analog and digital values can be read out at very short intervals (milliseconds)
Exact reading of the values in a self-defined time interval possible
With higher utilization via the Ethernet interface, the FIFO does not consume more traffic

Testing and programming

With our ICT tool, you can test and diagnose the FIFO-IN and FIFO-OUT with digital and analog I/Os.
You will also find help for correct programming in the source code of our FIFO sample programs.

General Handling

DapiOpenModule

This function opens a particular module.

DapiOpenModule

Description

This function opens a specific module

Definition

ULONG DapiOpenModule(ULONG moduleID, ULONG nr);

Parameters

moduleID=Specifies the module to be opened (see delib.h)
nr=Specifies which one (in case of several modules) should be opened.
nr=0 -> 1st module
nr=1 -> 2nd module

Return-Value

handle=Corresponding handle for the module
handle=0 -> module was not found

Comment

The handle returned by this function is needed to identify the module for all other functions.

Programming example

// Open USB module
handle = DapiOpenModule(RO_USB1, 0);
printf(“handle = %x\n”, handle);
if (handle==0)
{
// USB module was not found
printf(“Modul konnte nicht geöffnet werden\n”);
return;
}

DapiCloseModule

This command closes an opened module.

DapiCloseModule

Description

This command closes an open module.

Definition

ULONG DapiCloseModule(ULONG handle);

Parameters

handle=This is the handle of an open module

Return-Value

None

Programming example

// Close module
DapiCloseModule(handle);

DapiGetLastError

This function returns the last registered error. If an error has occurred, it must be deleted with DapiClearLastError(), otherwise any call of DapiGetLastError() will return the "old" error. If multiple modules are used, the use of DapiGetLastErrorByHandle() is recommended.

DapiGetLastError

Description

This function returns the last detected error. If an error occurred, it must be cleared with DapiClearLastError(), otherwise any call to DapiGetLastError() will return the “old” error.
If more than one module should be used, it is recommended to use DapiGetLastLastErrorByHandle().

Definition

ULONG DapiGetLastError(void);

Parameters

None

Return-Value

Error Code
0=no error. (see delib_error_codes.h)

Programming example

BOOL IsError()
{
unsigned char msg[500];
unsigned long error_code = DapiGetLastError();

if (error_code != DAPI_ERR_NONE)
{
DapiGetLastErrorText((unsigned char*) msg, sizeof(msg));
printf(“Error Code = 0x%x * Message = %s\n”, error_code, msg);

DapiClearLastError();

return TRUE;
}

return FALSE;
}

DapiGetLastErrorByHandle

This function returns the last registered error of a particular module (handle). If an error has occurred, it must be deleted with DapiClearLastErrorByHandle(), otherwise any call of DapiGetLastErrorByHandle() will return the "old" error.

DapiGetLastErrorByHandle

Description

This function returns the last detected error of a specific module (handle). If an error occurred, it must be cleared with DapiClearLastErrorByHandle(), otherwise any call to DapiGetLastErrorByHandle() will return the “old” error.

Definition

ULONG DapiGetLastErrorByHandle(ULONG handle);

Parameters

handle=This is the handle of an open module

Return-Value

Error Code
0=no error. (see delib_error_codes.h)

Programming example

BOOL IsError(ULONG handle)
{
unsigned long error_code = DapiGetLastErrorByHandle(handle);

if (error_code != DAPI_ERR_NONE)
{
printf(“Error detected on handle 0x%x – Error Code = 0x%x\n”, handle, error_code);

DapiClearLastErrorByHandle(handle);

return TRUE;
}

return FALSE;
}

DapiGetLastErrorText

This function reads the text of the last registered error. If an error has occurred, it must be cleared with DapiClearLastError(), otherwise every call of DapiGetLastErrorText() returns the "old" error. Definition

DapiGetLastErrorText

Description

This function reads the text of the last detected error. If an error occurred, it must be cleared with DapiClearLastError(), otherwise any call to DapiGetLastErrorText() will return the “old” error.

Definition

ULONG DapiGetLastErrorText(unsigned char * msg, unsigned long msg_length);

Parameters

msg = Buffer for the text to be received
msg_length = Length of the text buffer

Programming example

BOOL IsError()
{
unsigned char msg[500];
unsigned long error_code = DapiGetLastError();

if (error_code != DAPI_ERR_NONE)
{
DapiGetLastErrorText((unsigned char*) msg, sizeof(msg));
printf(“Error Code = 0x%x * Message = %s\n”, error_code, msg);

DapiClearLastError();

return TRUE;
}

return FALSE;
}

DapiClearLastError

This function deletes the last error registered with DapiGetLastError().

DapiClearLastError

Description

This function deletes the last error registered with DapiGetLastError().

Definition

void DapiGetLastError(void);

Parameters

None

Return value

None

Example program

BOOL IsError()
{
unsigned char msg[500];
unsigned long error_code = DapiGetLastError();

if (error_code != DAPI_ERR_NONE)
{
DapiGetLastErrorText((unsigned char*) msg, sizeof(msg));
printf(“Error Code = 0x%x * Message = %s\n”, error_code, msg);

DapiClearLastError();

return TRUE;
}

return FALSE;
}

DapiClearLastErrorByHandle

This function deletes the last error of a particular module (handle), which was registered with DapiGetLastErrorByHandle().

DapiClearLastErrorByHandle

Description

This function deletes the last error of a particular module (handle), which was registered with DapiGetLastErrorByHandle().

Definition

void DapiClearLastErrorByHandle(ULONG handle);

Parameters

handle=This is the handle of an opened module.

Return value

None

Example program

BOOL IsError(ULONG handle)
{
unsigned long error_code = DapiGetLastErrorByHandle(handle);

if (error_code != DAPI_ERR_NONE)
{
printf(“Error detected on handle 0x%x – Error Code = 0x%x\n”, handle, error_code);

DapiClearLastErrorByHandle(handle);

return TRUE;
}

return FALSE;
}

DapiGetDELIBVersion

This function returns the installed DELIB version.

DapiGetDELIBVersion

Description

This function returns the installed DELIB version.

Definition

ULONG DapiGetDELIBVersion(ULONG mode, ULONG par);

Parameters

mode=Mode with which the version is read (must always be 0).
par=This parameter is not defined (must always be 0).

Return-Value

version=Version number of the installed DELIB version [hex]

Programming example

version = DapiGetDELIBVersion(0, 0);
//With installed version 1.32 version = 132(hex)

DapiOpenModuleEx

This function opens a specific module with ethernet interface.The particularity of this command is,that parameters like IP-address, portnumber and the duration of the timeout can be specified. The opening of the module is independent of the DELIB Configuration Utility settings.

DapiOpenModuleEx

Description

This function specifically opens a module with an Ethernet interface. The parameters IP address, port number and the duration of the timeout can be determined.

Definition

ULONG DapiOpenModuleEx(ULONG moduleID, ULONG nr, unsigned char* exbuffer, 0);

Parameters

moduleID = Specifies the module to be opened (see delib.h)
nr = Specifies which one (in case of several modules) is to be opened
nr = 0 -> 1st module
nr = 1 -> 2nd module
exbuffer = buffer for IP address, port number and duration of the timeout

Return-Value

handle = Corresponding handle for the module
handle = 0 -> module was not found

Comment

The handle returned by this function is required to identify the module for all other functions.
This command is supported by all modules with Ethernet interface.

Programming example

// Open ETH-Module with parameter

DAPI_OPENMODULEEX_STRUCT open_buffer;

strcpy((char*) open_buffer.address, “192.168.1.10”);
open_buffer.portno = 0;
open_buffer.timeout = 5000;

handle = DapiOpenModuleEx(RO_ETH, 0, (unsigned char*) &open_buffer, 0);
printf(“Module handle = %x\n”, handle);

Digital output functions

DapiDOSet1

This is the command to set a single output.

DapiDOSet1

Description

This command sets a single output.

Definition

void DapiDOSet1(ULONG handle, ULONG ch, ULONG data);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output to be set (0 .. )
data= Specifies the data value to be written (0 / 1)

Return-Value

None

Requirements

The following SW feature bits must be supported by the module:

DAPI_SW_FEATURE_BIT_CFG_DO

The following conditions for the transfer parameters must be met:

maxCh = DapiSpecialCommand(handle, DAPI_SPECIAL_CMD_GET_MODULE_CONFIG, DAPI_SPECIAL_GET_MODULE_CONFIG_PAR_DO, 0, 0)
maxCh > ch

DapiDOSet8

This command sets 8 digital outputs simultaneously.

DapiDOSet8

Description

This command sets 8 digital outputs simultaneously.

Definition

void DapiDOSet8(ULONG handle, ULONG ch, ULONG data);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which writing is to start (0, 8, 16, 24, 32, ..)
data=Specifies the data values to be written

Return-Value

None

DapiDOSet16

This command sets 16 digital outputs simultaneously.

DapiDOSet16

Description

This command sets 16 digital outputs simultaneously.

Definition

void DapiDOSet16(ULONG handle, ULONG ch, ULONG data);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which writing is to start (0, 16, 32, ..)
data=Specifies the data values to be written

Return-Value

None

DapiDOSet32

This command sets 32 digital outputs simultaneously.

DapiDOSet32

Description

This command sets 32 digital outputs simultaneously.

Definition

void DapiDOSet32(ULONG handle, ULONG ch, ULONG data);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which writing is to start (0, 32, 64, ..)
data=Specifies the data values to be written

Return-Value

None

Programming example

// Write a value to the outputs
data = 0x0000ff00; // outputs 9-16 are set to 1
DapiDOSet32(handle, 0, data); // Chan Start = 0
printf(“Write to outputs data=0x%x\n”, data);
printf(“key for further\n”);
getch();
// —————————————————-
// Write a value to the outputs
data = 0x80000000; // Output 32 is set to 1
DapiDOSet32(handle, 0, data); // Chan Start = 0
printf(“Write to outputs data=0x%x\n”, data);
printf(“key for further\n”);
getch();
// —————————————————-
// Write a value to the outputs
data = 0x80000000; // Output 64 is set to 1
DapiDOSet32(handle, 32, data); // Chan Start = 32
printf(“Write to outputs data=0x%x\n”, data);
printf(“key for further\n”);
getch();

DapiDOSet64

This command is to set 64 digital outputs.

DapiDOSet64

Description

This command sets 64 digital outputs simultaneously.

Definition

void DapiDOSet64(ULONG handle, ULONG ch, ULONGLONG data);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which writing is to start (0, 64, ..)
data=Specifies the data values to be written

Return-Value

None

DapiDOClrBit32

With this command you can change the states of outputs to 0 without changing the states of the neighboring outputs.

DapiDOClrBit32

Description

This command can be used to switch outputs selectively to 0 without changing the states of adjacent outputs.

Definition

void DapiDOClrBit32(uint handle, uint ch, uint data);

Parameters

handle = This is the handle of an open module
ch = Specifies the number of the output from which writing is to start
data = Specifies the data value to be written (up to 32 bits)

Return-Value

None

Comment

Only the bits with a value of 1 in the data parameter are considered by the command.

Programming example

data = 0x1; // Output 0 would be changed to 0. The states of outputs 1-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xf; // Outputs 0-3 would be changed to 0. The states of outputs 4-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xff; // Outputs 0-7 would be changed to 0. The states of outputs 8-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xff000000; // Outputs 23-31 would be changed to 0. The states of outputs 0-21 won’t be changed
DapiDOSetBit32(handle, 0, data);

DapiDOSet1_WithTimer

This function sets a digital output (ch) to a value (data - 0 or 1) for a specified time in msec.

DapiDOSet1_WithTimer

Description

This function sets a digital output (ch) to a value (data – 0 or 1) for a certain time in ms.

Definition

void DapiDOSet1_WithTimer(ULONG handle, ULONG ch, ULONG data, ULONG time_ms);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output to be set (0 .. )
data= Specifies the data value to be written (0 / 1)
time_ms=Specifies the time in which the output is set [ms].

Return-Value

None

Comment

This command is supported by all output modules of the NET series as well as by our RO-O8-R8 module.
This command loses its validity if it is overwritten with other values.
If you want to deactivate the command, it must be overwritten with time_ms=0.

Programming example

DapiDOSet1_WithTimer(handle, 2, 1, 1000);
//Setting channel 2 for 1000msec to 1

DapiDOSetBit32

With this command you can change the states of outputs to 1 without changing the states of the neighboring outputs.

DapiDOSetBit32

Description

This command can be used to switch outputs selectively to 1 without changing the states of adjacent outputs.

Definition

void DapiDOSetBit32(uint handle, uint ch, uint data);

Parameters

handle = This is the handle of an open module
ch = Specifies the number of the output from which writing is to start
data = Specifies the data value to be written (up to 32 bits)

Return-Value

None

Comment

Only the bits with a value of 1 in the data parameter are considered by the command.

Programming example

data = 0x1; // Output 0 would be changed to 1. The states of outputs 1-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xf; // Outputs 0-3 would be changed to 1. The states of outputs 4-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xff; // Outputs 0-7 would be changed to 1. The states of outputs 8-31 won’t be changed
DapiDOSetBit32(handle, 0, data);

data = 0xff000000; // Outputs 23-31 would be changed to 1. The states of outputs 0-21 won’t be changed
DapiDOSetBit32(handle, 0, data);

DapiDOReadback32

This command reads back the 32 digital outputs.

DapiDOReadback32

Description

This command reads back the 32 digital outputs.

Definition

ULONG DapiDOReadback32(ULONG handle, ULONG ch);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which the read back is to be performed (0, 32, 64, ..)

Return-Value

Status of 32 outputs.

DapiDOReadback64

This command reads the current PWM frequency of the module

DapiDOReadback32

Description

This command reads back the 32 digital outputs.

Definition

ULONG DapiDOReadback32(ULONG handle, ULONG ch);

Parameters

handle=This is the handle of an open module
ch= Specifies the number of the output from which the read back is to be performed (0, 32, 64, ..)

Return-Value

Status of 32 outputs.

Web Interface – Interface

All DEDITEC Ethernet modules have a web interface that allows you to make settings conveniently via your web browser and also gives you direct access to the I/Os.

This allows you to access the product with a smartphone, tablet or even a PC via a browser.

The following I/O units are supported:

Digital inputs
Digital inputs (counter function)
Digital outputs
Analog inputs (voltage & current)
Analogue outputs (voltage & current)
PT100 temperature detection
Stepper motor control

You can protect the Ethernet module against unauthorized access with a user system and optional encryption system.

General

Start page of the web interface. The navigation on the left side gives you access to various setting options.

Network configuration

All network settings can be made directly via the web interface.

Usermanager

Here you can define the user name and password for access to the web interface. If the user is inactive, he/she is automatically logged out after the session time has expired.

Status / Reboot

Version of the installed firmware. Functions for restarting and resetting the settings.

Security

In addition to a user/password system for the web interface, we also offer you the option of encrypting the entire network communication. Access to the I/Os can also be blocked.

Supported I/Os

In the following we show you the supported I/Os that you can operate via the web interface.

Digital Inputs

The picture shows the overview of the digital inputs. You can switch between several inputs via the drop-down menu. The column ‘State’ shows whether a signal is present at the input.

Digital Inputs Counter

Our digital inputs have a counting function. The counter reading can be read and reset via the web interface.

Digital Outputs

The digital outputs can be switched via an on/off button. The current status of the outputs can be read back via the ‘Readback’ column.

Analogue Inputs

Current and voltage can also be read out via the web interface. The desired operating mode can be set via the A/D Mode drop-down menu.

Analogue Outputs

Analogue signals can also be output via the web interface. The desired D/A mode can be set via the drop-down menu, as with the analog inputs. The desired value can be written to the outputs using the ‘SET’ button. The column ‘Readback’ shows the current voltage/current output of the D/A converter.

Temperature measurement (PT100)

The temperature measurement is supported by our RO series.

PT100

The current temperature can be read. If no sensor is connected to the channel, this is signalled with ‘disconnected’.

Stepper-Motor Control

The position and speed of the stepper motor can be set via the control elements. The status window shows the current position, temperature and power supply.

I/O Control APP for Android™

Control the digital and analog I/Os of our Ethernet modules from on the road. With the DEDITEC I/O control Android App, any network-compatible Android device can be remotely controlled for DEDITEC products with Ethernet interface

Features:

Separate storage of network settings for private and public networks
Better clarity through configurable I/O names
Configurable refresh of all I/Os

The following I/Os are supported:

up to 128 analog inputs (0..10V, 0..5V, +/- 10V and +/- 5V)
up to 64 analog outputs (0..10V, 0..5V, +/- 10V and +/- 5V)
up to 128 digital inputs and outputs

Network settings
A configuration for private (WLAN) or public (Internet) networks can be created and saved in the network settings.

Module configuration

At the module configuration you see the number of connected I/O modules.

You can also select here which I/Os are to be controlled.

Digital inputs
The digital inputs are scanned at an adjustable interval.

Digital outputs
In the area of the digital outputs the channels can be switched on or off individually.

It is also possible to switch all channels on or off.

Analogue inputs
For the analog inputs you can select from the measuring ranges 0..10V, 0..5V, +/- 10V or +/- 5V.

The A/D channels are scanned automatically at an adjustable interval.

Analogue outputs
Here you may set analog outputs in the measuring range 0..10V, 0..5V, +/- 10V or +/- 5V.

Settings
This picture shows the settings for analog outputs. Each channel can be given a name here.

It can also be defined here whether and at what interval the analog outputs are read back.

These settings are available for all I/Os.

Block diagram NET-DEV-REL4

Connection example Changeover relay

Connection example

Manual

Manual NET-Serie

Hard- und Software description

Download

Description NET-CPU Modules
Description NET-DEV Digital Modules

DELIB driver library

Manual of the DELIB driver library

Documentation of all functions for the driver library

Download

Windows 10, 8, Vista, 7, XP, 2000 andLinux
Moduel open/close functions
Digital inputs: reading 1 / 8 / 16 / 32 / 64 bit
Digital outputs: Write 1 / 8 / 16 / 32 / 64 bit
A/D Lesen: read, read_volt, read_mA, A/D Modus einstellen
D/A schreiben: write, write_volt, write_mA, D/A-Modus einstellen

DELIB (64-bit) driver library for Windows

For Windows 11/10, Windows 7, Windows 8, Vista, XP and 2000

Download

Installation file for the 64 bit DELIB driver library.

The following operating systems are supported:

64 bit

Windows 11/10 x64
Windows 7 x64
Windows 8 x64
Windows Server 2012 x64
Windows Server 2008 x64
Windows Vista x64
Windows XP x64
Windows Server 2003 x64

Included software

DT-Flasher x64
Software to update DEDITEC module to the latest version
DELIB Configuration Utility x64
Set configuration of module addresses
DELIB Module Config x64
Configuration of module-specific settings
CAN Configuration Utility x64
Set configuration of CAN modules
DELIB Module Demo x64
Enables manual switching of a module
DELIB Command Line Interface x64
Enables the execution of DELIB commands in the command line
Watchdog Configuration Utility x64
Set configuration of a watchdog stick

DELIB (32-bit) driver library for Windows

For Windows 11/10, Windows 7, Windows 8, Vista, XP and 2000

Download

Installation file for the 32-bit version of the DELIB driver library.

The following operating systems are compatible:
32-Bit

- Windows 11/10
- Windows 7
- Windows 8
- Windows Server 2012
- Windows Server 2008
- Windows Vista
- Windows XP
- Windows Server 2003

64-Bit

Windows 10 x64
Windows 7 x64
Windows 8 x64
Windows Server 2012 x64
Windows Server 2008 x64
Windows Vista x64
Windows XP x64
Windows Server 2003 x64

Included software

DT-Flasher
Software to update DEDITEC module to the latest version
DELIB Configuration Utility
Set configuration of module addresses
DELIB Module Config
Configuration of module-specific settings
CAN Configuration Utility
Set configuration of CAN modules
DELIB Module Demo
Enables manual switching of a module
DELIB Command Line Interface
Enables the execution of DELIB commands in the command line
Watchdog Configuration Utility
Set configuration of a watchdog stick

Attention:

With this version of the driver library, only 32-bit applications can be created, which can then be run on 32- and 64-bit systems.

DELIB driver library for Linux (32/64-bit)

For 32/64-bit Linux distributions starting with kernel 2.6.x

Download

DELIB driver library for Linux distributions (32/64-bit) starting with kernel 2.6.x

This driver package includes the following components:

DELIB USB driver
DELIB Ethernet driver
DELIB CLI

DELIB USB driver

Supports the following products:

NET-Series (via USB interface)
RO-USB-Series
BS-USB-Series
USB-Mini-Sticks
USB-Watchdog
USB-OPTION-8 / USB-RELAIS-8
USB-TTL-32 / USB-TTL-64

Note:

With the standard USB driver, you can access several USB products with different module IDs (for example one RO-USB and one USB-OPTOIN-8). Therefore, no additional driver installation is required.

If you want to access several USB products with the same module ID (for example one USB-OPTOIN-8 and one USB-RELAIS-8), you have to install additionally the Linux FTDI driver. The FTDI driver can be found at http://www.ftdichip.com.

DELIB Ethernet driver

Supports the following products:

NET-Series (via Ethernet Interface)
RO-ETH-Series
RO-ETH/LC-Series
BS-ETH-Serie
ETH-OPTION-8 / ETH-RELAIS-8
ETH-TTL-64

DELIB CLI

With the DELIB CLI (Command Line Interface) for Linux it is possible so controll all I/O’s over the command-line.

DELIB - Sample-Sources - Installer (approx. 10 MB)

Sample programs for different programming languages (Also in DELIB Setup included)

Download

Sample programs for different programming languages (Also in DELIB Setup included)

C (Microsoft Visual C++ 6.0, Borland C)
C++ (Microsoft Visual C++ 6.0)
C# (Microsoft Visual C# 2008 to 2015)
Delphi (Borland Delphi 7)
VB (Microsoft Visual Basic 6.0)
VB.NET (Microsoft Visual Basic 2008 to 2015)
Java (Java native interface)
Java.dll (Ethernet protocol for ethernet products)

Download

Hardware-Updates (Firmware)

Flash files for the DT-Flasher

Download

The flash files can also be downloaded directly in the DT-Flasher.

This package contains firmware files for the following products:

STARTER-series:

USB-MINI-Sticks
USB-8-er Opto/Relay
Ethernet 8-er Opto/Relay
USB-TTL I/O
Ethernet-TTL I/O

BS-series:

BS-CAN Module
BS-ETH Module
BS-USB Module
BS-SER Module

RO-series Interfaces:

RO-USB
RO-SER
RO-ETH
RO-ETH/LC
RO-CAN

RO-series I/Os:

AD / DA Module
CNT8 / CNT-IGR
O8-R8 Time module
PT100
Stepper2

Development accessories

USB Controller 8
USB Watchdog Stick

6 pin connector

Required to connect your application to the DEDITEC module.

Type: Phoenix Contact 1709556
Push-in spring connection
Without switching capacity!
Connection for all conductor types from 0.2mm² to 2.5mm²
Pluggable

DIN rail connector

The DIN-Rail connector is a single BUS segment which allows the connection to other modules. It is clipped into the DIN-rail and plugged into the side of an existing DIN-Rail connector.

DIN-Rail Bus Connectors
Connection of a NET or COS module
For extension of the NET or COS bus system
1 piece

Power supply 24V/2A for DIN rail mounting

The DR-4524 from Mean Well is a 48W rail mount power supply for industrial applications. It offers protection against short circuit, overload, overvoltage and overheating.

Input voltage range: 85V… 264V AC / 120V DC … 370V DC
Output voltage: 24V DC
Output current: 2A
Nominal power: 48W

12V din rail relay

PLC interface for limiting continuous currents up to 10A, consisting of basic terminal with screw connection and pluggable miniature relay. Mountable on NS 35/7.5 mounting rail.

Nominal voltage: 230V AC / 220V DC
Switching voltage: 250 V AC/DC
1 changeover contact
Reverse polarity protection, freewheeling diode
LED for voltage indication
Phoenix Contact, 2967617, PLC-RSC- 12DC/21HC

24V din rail relay

PLC interface for limiting continuous currents up to 10A, consisting of basic terminal with screw connection and pluggable miniature relay. Mountable on NS 35/7.5 DIN rail.

Nominal voltage: 24V AC/DC
Switching voltage: 250 V AC/DC
1 changeover contact
Reverse polarity protection, freewheeling diode
LED for voltage indication
Phoenix Contact, 2967633, PLC-RSC- 24UC/21HC

230V din rail relay

With this 230V relay can you reduce your voltage to 12V. The 12V signal can be read by our opto coupler inputs.

Max switching current 250V AC
Coil current 4,5mA

DIN rail connector

The DIN-Rail connector is a single BUS segment which allows the connection to other modules. It is clipped into the DIN-rail and plugged into the side of an existing DIN-Rail connector.

DIN-Rail Bus Connectors
Connection of a NET or COS module
For extension of the NET or COS bus system
1 piece

6 pin connector

Required to connect your application to the DEDITEC module.

Type: Phoenix Contact 1709556
Push-in spring connection
Without switching capacity!
Connection for all conductor types from 0.2mm² to 2.5mm²
Pluggable

Tool for wiring connectors

Serves to open and close the clamp contacts on the Wago connectors.

Type: Wago Kontakttechnik 734-231

DIN Rail

Top-hat rail for mounting our control technology modules.

Top-hat rail according to DIN EN 50022
Type: Phoenix Contact / 1208131
Dimensions in mm: 450 x 35 x 7.5 (L x W x D)

Reviews

There are no reviews yet.

Be the first to review “NET-DEV module with 4 changeover relay outputs (12A)”

Use our advantages

Lifetime
updates

Free soft- & hardware(firmware)-updates.
Enjoy our lifetime update service.

5 years
Delivery availability

We offer at least 5 years delivery availability for our products.
Our experience shows that it is even about 10 years.

Questions about the product? Product support

Do you have any technical or commercial questions about the product before you buy?
Please contact us in advance.

Customer-
modifications

Our products often serve as the basis for customer-specific solutions.
Just get in touch with us.

We are
always there for you!

Since its foundation in 2008, Dipl. Ing. Jürgen Siebert has been the managing director of DEDITEC GmbH. He will also be happy to advise you personally.

Product- & Service-Hotline: +49 (0) 22 32 / 50 40 8 – 40

Questions about the product or order: support@deditec.de

NET-DEV module with 4 changeover relay outputs (12A)

OUR PROMISE TO YOU:

General

Relay outputs

Additional information

General Handling

DapiClearLastError

Description

Definition

DapiClearLastErrorByHandle

Description

Digital output functions

Connection example Changeover relay

Manual

DELIB driver library

DELIB USB driver

DELIB Ethernet driver

DELIB CLI

Download

Reviews