The BS-WEU-AD16-DA4-OR16 is a compact module with an Ethernet and USB interface. Furthermore, you can integrate and control this module via WiFi into your PC network.
3 different module variants
- with 16 A/D channels
- with 16 A/D channels , 4 D/A channels
- with 16 A/D channels , 4 D/A channels, 16 DI/DO channels
- CAN and SER interface (see scope of delivery)
- A/D current and voltage modes (see scope of delivery)
- Ethernet-Interface 10/100 Mbit
- Connection via WiFi possible
- WPS function
- Open Ethernet protocol
- USB 2.0 interface up to 480 Mbit
- 16 * A/D inputs with 16-bit resolution each
- Voltage ranges: 0-5V, 0-10V, ±5V, ±10V
- Current ranges optional: 0-50mA
- 4 * D/A outputs with 16-bit resolution each
- Voltage ranges: 0-5V, 0-10V, ±5V, ±10V
WEU Modules (WEU= WiFi, Ethernet, USB) can be connected to the PC network via Ethernet or USB interface, but also via WiFi. For a more user-friendly connection setup via WiFi, the module can also be connected to the router via WPS function.
Analog to digital converter modules are suitable for measuring and monitoring voltages and currents. Measuring transducers, for example, convert physical quantities such as pressure, temperature, humidity etc. into corresponding currents (0..24mA) or voltages (0..10V) and can thus be recorded and digitally processed with our A/D modules.
With our digital to analog converter modules you are able to control current or voltage controlled actuators such as valves, servomotors or special power supplies. Especially in harsh industrial environments and with very long cable runs, analog signals, especially currents, can be transmitted interference-free.
With our optocoupler inputs, digital signal states can be recorded within a voltage range of 5V to 30V AC or DC. Input and output circuits are galvanically isolated from each other up to 2.5kV.
Digital In Input Filter
With our Digital-In modules, an input filter can be set in a time interval of 1ms…255ms to filter interference pulses.
This means that AC signals can also be detected cleanly.
Each input has a 16 bit counter that can count up to 65535 pulses. If the maximum counter value is exceeded, the counting process starts again from zero. By means of a software command, the current status of all input counters can be read from the module simultaneously.
Recording of status changes
Status changes that occur between the readout cycles are reliably detected by internal flip-flops and can be read out separately by software. In addition, such an event is signalled by a status LED. Resetting is done automatically after the flip-flops have been read out.
With the option “Relay outputs (1A)” reed relays with normally open (NO) function are used. They are suitable for smaller switching capacities of up to 1A and have a service life of well over 100 million switching cycles. The electrical isolation between input and output circuit is up to 1.5kV.
If communication with the DEDITEC module is interrupted in a timeout case, the timeout protection function takes effect. It can be set for each digital output whether it is to be “switched off”, “switched on” or left unchanged. Motors can thus be switched off in a timeout case, for example, and connected horns or other alarm transmitters can be switched on.
New timeout modes
3 different timeout modes: “normal”, “auto reactive” and “secure outputs” for different procedures in case of a timeout event.
In “secure outputs” timeout mode, access to the outputs is blocked after a timeout event, thus preventing further access to the outputs.
Unlocking must be done by an additional software command.
With the option “Relay outputs (3A)” power relays with normally open (NO) function are used. They are suitable for switching capacities of up to 3A and have a service life of up to 10 million switching cycles. The electrical isolation between input and output circuit is up to 3kV.
With the option “Mosfet outputs (2A)” P-Ch MOSFETs are used. They are suitable for switching capacities up to 2A DC and are practically wear-free.
A screwless system from the manufacturer WAGO Kontakttechnik is used as the connector. The 1-wire female connectors are 100% protected against mismating and have an eject and locking mechanism. All conductor types up to 1.5mm² can be connected.
Software and control
Our DELIB driver library, which is included with the product, makes it easy to address the product via our API.
We offer support for the following programming languages:
We offer support for the following operating systems:
- Windows 10 (32bit/64bit)
- Windows 8/8.1 (32bit/64bit)
- Windows 7 (32bit/64bit)
- Windows Vista (32bit/64bit)
- Windows XP (32bit/64bit)
- Windows Server 2003 (32bit/64bit)
- Windows 2000
Corresponding programming examples can be found in the “Software” section of the products or are included on the driver CD.
Remote switching of IP modules
Our IP modules can be conveniently and easily controlled from home anywhere in the world via the TCP-IP network. The following free options are available to you for this purpose.
Our Module Config is included in the DEDITEC driver library. With the help of this software, you can configure, control and test your DEDITEC modules.
DEDITEC I/O-Control App:
Configure your DEDITEC modules easily via smartphone. With our DEDITEC I/O Control app, our modules can also be controlled while on the move.
Our IP modules can be operated from any browser. All you need is the IP address of the module.
There are no reviews yet.