RS-232/RS-485-input module with 64 optical decoupled switching inputs

A product identical in construction with USB interface is to be found here ( -> RO-USB-O64 - USB-input module with 64 optical decoupled switching inputs)

RS-232/RS-485-interface

RS-232/RS-485-interface connection (galvanic isolated)

By using a 9 pin D-SUB connector the module will be connected to the PC or any other device using a serial interface.The module interface is galvanic isolated from connected devices by using an optocoupler.

Inputs

Visual monitoring of inputs

The state of every input is directly indicated by a LED. That way, wrong wiring is easily noticeable.

Detecting short input pulses

The module won't miss fast state changes, even if the inputs are sampled in larger periods. Fast state changes between two readout-cycles are detected through an additional logic and can be readout by software. A LED (combined for all inputs) indicates a "state change". The LED does not extinguish until the software register for input state changes is read out.

Counter

Every input channel has a 16 bit counter. Herewith the module "counts" additional events.

Input protection using optocoupler

The inputs have AC-suitable optocouplers. Therefore you don't need to pay attention to the polarity while wiring the inputs.

Input voltage

By default the inputs are designed for a voltage of 24V. They can be adjusted (even later) to 15V, 12V or 5V.

Relay Outputs

Relay-outputs (galvanically isolated, permanent load of 1A AC)

Relays ensure a save galvanic isolation of the outputs. They are designed for up to 36V/1A. Maximum switchable power is 20W.

Timeout-protection

If required, a timeout-protection may be enabled, switching automatically off the outputs to prevent damage. This takes place, when e.g. the communication gets lost. Switching off the outputs is indicated by a LED.

Connector

Easy to maintain connector system

The plug and socket consist of a multipoint socket connector and a multipin connector with a throw-off lever. Plug-in and plug-out is easy as well as rewiring the terminal strip. The wire connection itself is realized with a screwless connector system. A tool is included with each module.

Configuration of the RS-232/RS-485 Module

A brand new serial module is delivered in RS-232 mode. To change this mode to RS-485, you just have to open the case and place some jumper. Detailed information can be found in the manual RO-Serie

RS-232/RS-485 parameter configuration

All serial parameter can be configured by a few DIP switches. Such as baudrate, module address, special-mode and other interface specifications. The special-mode allows you to set the module on constant values. This may be useful for a quick start-up and defect analysis.

RS-232 / RS-485-Interface
Power Supply	7V bis 24V DC (über zweipolige steckbare Schraubklemme)
Interface	RS-232/RS-485 (galvanic isolated using optocoupler) Connection by 9 pin. D-SUB socket One LED for each 3,3V and 5V Voltage feed Baud rate: 1,25 MBit - 300 Bit
Control-LED	RS-232/RS-485 -activity ERROR Input state change (only for digital outputs) Timeout (only for outputs) I/O Module access

Optocoupler-Input-Module
Inputs	64 Opto-In-Inputs Galvanic isolated using optocoupler 24V AC switching voltage (optional as well available for 15V, 12V, or 5V) 16 Bit-counter per input channel Logging of impulses between 2 read out cycles
Activity-LED	A LED for each input channel
Connectors	16 pin pluggable terminal block each 8 inputs

General
Operating temperature	+10°C...+50°C
Dimensions	208 mm x 126 mm x 31 mm (lxwxh)

The block diagram illustrates how the module is constructed.

Controlling of our RS-232/RS-485 modules

Our RS-232/RS-485 modules can be controlled by two different ways.

1. The Windows driver library DELIB

The DELIB driver library allows a direct communication of our modules. You don't have to worry about the Handshake and the serial protocoll. The DELIB DLL assumes it for you!

2. You may program the controlling software by yourself

In our download area you can find a conform protocol. So our serial modules can be connected to small Linux computers or workstations for engineering, with RS-232/RS485 Interface.

Controlling by the DELIB driver library under Windows

The extensive but easy handling library is written for computer language, which responds to DLL's. Programming examples in source code for C, Delphi or Visual Basic can be found in our download area.

Examples for responsing our products with "C"

In the following example we show you in "C", how to access to our input modules in short time.

1. Step: Open the module

handle = DapiOpenModule(RO-SER,0); // Open serial module

2. Step: Reading of 16 digital inputs

data = DapiDIGet16(handle, 0); // Read the first 16 digital inputs

3. Step: Close the module

DapiCloseModule(handle); // Close the module

The function "DapiOpenModule" is used to open a special kind of module. Which module should be openend, is defined by the two parameters. The first parameter is for the "module ID". By the integrated "DELIB.H", you can also set this parameter to "RO-SER". So the driver library recognize, that a serial interface will be driven.

The second parameter assigns the module number. If only one module is connected to the pc, the module number is "0". Are there more than one module in the network, you have to set the correct number. The link to the according IP-address of the module can be configured by the "DELIB-Configuration Utility".

Testprogram with examples for digital inputs

Digital Input/Output Sample Testprogramm für Module

Digital Input/Output Sample Testprogramm für Module

Click to enlarge

With this program you can test our modules very easily. The digital input/output sample testprogram is easy to use and supports all of our measurement modules. The example above shows the test of a RO-USB-O32 input module.

Controlling by the open source ethernet protocol

If required, you can program your own controlling software. The according communication protocol is disclosed. The modules will be controlled by register. Therefore we designed an open source communication protocol, which allows to respond to the modules and excecute read/write commands. The manual "Serial Protocol" describes transmission and receiving frames, to communicate with our serial modules.

Overview about available DELIB-Functions

Plug connection

Screwless plug connectors

All input and output connectors have a practical, screwless terminal block. An mechanic ejection guarantees a very quick module change without any special tools. Wire connection happens with screwdriver or an included plastic pin. (s. pic.1)

Pic1:

Connection example of a RO-Module

		RO-MODULE
		Step 1: Push the plastic tool into the small notch at the side of the terminal block, to open the clamp contacts for the wire connection.
		Step 2: When you are looking into the wire hole, you can see, that the clamp contacts have been opened. The end of the wire should be bared 5-7mm. Now put it as deep as possible into the opened hole.
		Step 3: After that, pull the plastic tool out of the notch. The clamp is closed again now.
		Step 4: After correct connecting, pull out the wiring by hand isn't no more possible

Manuals

Datasheets

Driver / Programs

Downloads

Demo-Software